top of page

Low NC Noise Criteria for HVAC Design in Saudi Arabia

12 hours ago
9 min read

Room-by-Room NC Targets, Octave-Band Calculations, Low-Noise Equipment Selection, and Commissioning for Saudi HVAC Projects


Direct answer


Specify the Noise Criteria (NC) target for each critical room. Predict the octave-band sound pressure at the receiver, combine all significant HVAC paths by energy, and compare each band with the adopted target curve. Treat the controlling band and verify the room after TAB.


A room can miss its HVAC background noise target because of one octave band, even when the overall sound level seems acceptable. Designing for low Noise Criteria (NC) starts with a target for each room, then follows sound from the fan, ductwork, terminals and structure to the occupant. This guide shows how to check an NC-25 target and identify the path that needs treatment.


Where HVAC noise reaches a quiet room


Use the source–path–receiver method. Identify equipment and flow noise, trace each transmission path and estimate the octave-band sound pressure where occupants will hear it. One air handling unit (AHU) can reach a room through several paths at the same time.


  • Ductborne sound travels through supply and return systems. Fan sound, terminal discharge noise and return-air paths can all contribute to the same room.


  • Regenerated sound is produced by airflow at dampers, elbows, transitions and diffusers. It can become dominant downstream of a silencer.


  • Breakout and radiated sound pass through duct walls, terminal casings and ceilings. Return openings and shared plenums can provide additional paths.


  • Structure-borne vibration passes through supports, slabs and connected piping or ductwork and can radiate as sound from room surfaces.


Equipment sound power describes the source. NC is evaluated with octave-band sound pressure at the receiver. Convert the source data using the applicable propagation and room corrections before comparing it with the room limits.



HVAC source–path–receiver diagram showing an AHU or fan, supply and return ducts, duct or casing breakout, structure-borne vibration and the receiving room.

Figure 1. Low-NC HVAC design starts by tracing ductborne sound, breakout and vibration from the source to the receiver.


Eight engineering checks for low-NC HVAC design


1. Define the NC target by room and operating mode


List the spaces where HVAC noise matters and agree on the applicable curve, frequency range, measurement positions and operating conditions. Consider full load, typical use and quiet-night or turndown operation where relevant.


Engineering checks: room function, indoor criterion, acoustic test standard or method, operating modes and owner approval.


2. Obtain octave-band source sound power at duty


Request inlet, discharge and casing-radiated sound data as applicable for AHUs, fans, VAV terminals, fan coils and grilles. Review sound at the scheduled airflow, static pressure, speed and available part-load points. Use the supplier’s acoustic test basis to compare like configurations.


Engineering checks: octave-band Lw, airflow, pressure, speed, equipment configuration and test standard.


3. Map the paths to each receiver


Trace supply, return, breakout, casing radiation, cross-talk and vibration. Use the actual routing, fittings, ceiling construction and receiver position. Account for sound generated downstream, including a damper or diffuser near the room.


Engineering checks: marked-up drawings, partitions, shafts, plenums, duct details, supports and service connections.


4. Calculate octave-band sound pressure and combine paths


Apply path-specific attenuation and room corrections to estimate the sound pressure from each source at the receiver. Combine independent paths in each band with Lp,total = 10 log₁₀(Σ 10^(Lp,i/10)). Two independent 30 dB contributions produce approximately 33 dB in that band.


Engineering checks: consistent references, room correction, receiver positions, individual path results and energy sums. AHRI 885 provides a calculation procedure for air terminals and outlets.


5. Find the controlling band against the NC curve


Compare the total room spectrum with the specified limit band by band. Report the band that sets or exceeds the target, then identify its largest path contributions. Check for low-frequency rumble or tones when the room use or project specification warrants more than the NC rating.


Engineering checks: adopted reference curve, level and margin by band, source ranking and any supplementary acoustic criteria.


6. Reduce noise at the source and along the path


Review fan selection and pressure losses, lower unnecessary terminal inlet pressure and locate dampers away from outlets where feasible. Where silencers are required, compare insertion loss in the controlling band with regenerated sound and pressure drop at the actual velocity. Coordinate breakout treatment and vibration isolation where those paths matter.


Engineering checks: fan duty and stable operation, terminal sound data, silencer performance, access and isolation details.


7. Coordinate acoustics with cooling and controls


Evaluate the actual airflow, pressure and control sequence for high-ambient cooling and for lower-load modes. Maintain the approved ventilation and room-pressure relationships while correcting noise. Confirm that filters, louvers and silencers are reflected in the fan’s final duty.


Engineering checks: summer duty, approved ventilation, static pressure reset, filter loading allowance, room pressure and operating modes.


8. Verify installed room sound after TAB


Complete testing, adjusting and balancing (TAB), confirm fan speed and terminal settings, then measure the room spectrum in the agreed modes. Document furnished or finished conditions and microphone positions, and assess background noise in accordance with the project’s measurement procedure.


Engineering checks: calibrated octave-band instrumentation, operating logs, background readings, NC result and corrective-action records.


Worked NC-25 example using octave-band sound pressure


Assume the project adopts the traditional 63–8,000 Hz NC curves commonly used for HVAC design. In frequency order (63, 125, 250, 500, 1,000, 2,000, 4,000 and 8,000 Hz), the NC-25 limits are 54, 44, 37, 31, 27, 24, 22 and 21 dB. The predicted room values are 51, 42, 35, 33, 26, 23, 21 and 20 dB. The 500 Hz result is 2 dB over the limit. The spectrum is above NC-25 but within NC-30 when compared with those two plotted curves. The adopted rating procedure determines how an exact rating is reported.


Check

Example input or result

Design implication

500 Hz target

31 dB for NC-25

Use the project’s specified curve.

Supply path before treatment

30 dB at the receiver

Check terminal discharge and downstream fittings.

Return path before treatment

30 dB at the receiver

Check the return-air transmission path.

Combined before treatment

33.0 dB from 30 and 30 dB

2.0 dB above target at 500 Hz.

Individual paths after treatment

24 dB supply and 25 dB return

Illustrative reductions of 6 and 5 dB.

Combined after treatment

27.5 dB from 24 and 25 dB

About 3.5 dB below target at 500 Hz. Recalculate the other bands.



Bar chart comparing eight predicted room octave bands with NC-25. Only 500 Hz exceeds the curve, by 2 dB.

Figure 2. The predicted sound pressure exceeds the NC-25 limit by 2 dB at 500 Hz. Every other illustrated octave band is below the target.


Saudi Arabia HVAC design and acceptance requirements


Set the indoor target from the project acoustic brief and room function. ASHRAE’s HVAC Applications guidance provides starting points. For example, a specialty conference room may warrant a target as low as NC/RC 25. Coordinate the specific NC curve, calculation method and test protocol with the project acoustician.

For Saudi facilities, include the cooling airflow and static pressure expected in summer operation. Verify the fan and terminal operating points for the design load as well as modes such as quiet-night operation and variable-air-volume turndown where specified.


Coordinate ventilation rates, filtration, room pressure and temperature control with acoustics. In healthcare or other controlled spaces, choose noise reductions that maintain the documented airflow and pressurization requirements.

For equipment near façades, roofs or adjacent sites, assess outdoor noise at the relevant receivers under the applicable requirements. Document indoor NC and external noise acceptance in the project acoustic schedule.



Project acceptance boundary

Agree on the indoor NC curve, test conditions, acceptable background correction and any additional tonal or low-frequency criteria. Outdoor noise assessment should use the applicable outdoor receiver requirements.

Discuss an HVAC acoustic design review with ASPAR Engineering


What to include in a low-NC design and RFQ data pack


Keep the room schedule, source sound data, acoustic path calculations and acceptance test plan in one coordinated submission. Require bidders to state the selected operating point, acoustic data basis and any room-correction assumptions.


Data pack category

Minimum information

Room acoustic schedule

Room function, target NC, other acoustic criteria and operational scenarios.

Equipment sound data

Octave-band sound power, duty points, inlet or discharge data and casing radiation.

Path and architectural data

Duct geometry, fittings, silencers, terminals, plenum and ceiling build-up, and structural details.

Predicted receiver sound

Path-by-path and total octave-band sound pressure, receiver locations and margin by band.

Verification plan

TAB records, occupancy and equipment conditions, test locations, method and acceptance reporting.


Typical Saudi project risks to review


  • Copying a supplier’s catalog NC value into the room schedule without checking its assumed room attenuation and operating point.


  • Selecting a terminal for design airflow but overlooking the actual inlet pressure or damper position.


  • Omitting return-air paths, duct breakout or terminal casing radiation above a lightweight ceiling.


  • Using a silencer’s headline insertion loss without checking the governing band, pressure loss and regenerated sound.


  • Reviewing only peak airflow and overlooking nighttime turndown, fan staging or low-frequency control instability.


  • Accepting an overall dBA reading where the specification requires octave-band sound pressure and an NC rating.


Delivery workflow from room targets to acoustic handover


  1. Agree on room-by-room NC targets, operating modes and the acceptance procedure.


  2. Obtain octave-band equipment sound power at the scheduled duties.


  3. Trace ductborne, radiated and structure-borne sound paths to each critical receiver.


  4. Calculate and combine receiver sound pressure by octave band.


  5. Identify the controlling band and verify the acoustic effects of proposed treatments.


  6. Complete TAB and test the required room and equipment conditions.


  7. Issue the acoustic calculation, measured spectra and closeout records.


Consultant checklist for low-NC HVAC design


☐ Room-by-room targets and the adopted NC curve and rating method are recorded.


☐ Equipment sound power data reflect the scheduled airflow, pressure and operating mode.


☐ Supply, return, breakout, casing radiation and vibration paths are included.


☐ Room contributions are combined logarithmically in each octave band.


☐ Silencer insertion loss, pressure drop and regenerated sound are checked at duty.


☐ Full-load, part-load and night operating cases are included where applicable.


☐ TAB, acoustic measurement positions, background conditions and reporting are agreed.


How ASPAR Engineering can support low-NC HVAC design


ASPAR Engineering can support Saudi projects through HVAC equipment selection, engineering analysis and commissioning. The scope can include review of room criteria, source data, transmission paths and the installation details affecting noise at the receiver.

Share the room schedule, plant layout and equipment submittals so the team can identify the critical rooms and agree on calculation and testing requirements.


Planning low-NC HVAC design in Saudi Arabia?

Send the room criteria, HVAC layout, airflow schedules and available octave-band equipment data.

Request an HVAC acoustic review — info@aspar.engineer · +966 59 662 9319


Related ASPAR Engineering pages and technical guides


These resources cover HVAC acoustic design, hospital-specific criteria, equipment selection and commissioning in Saudi Arabia.








Frequently asked questions


What does NC-25 mean in HVAC design?


NC-25 identifies a reference curve with a different sound pressure limit at each octave-band center frequency. Under a curve-limit specification, the room meets NC-25 when all required bands are at or below the curve under the specified test conditions.

For example, the traditional NC-25 curve allows 44 dB at 125 Hz and 31 dB at 500 Hz. Compare the room result with the curve and frequency range identified in the project requirements.


Is NC-25 the same as 25 dBA?


NC-25 rates an octave-band spectrum against an NC curve. A dBA value represents the overall A-weighted sound pressure level. The same dBA level can be associated with different octave-band spectra and different NC ratings.


Will an NC-25 diffuser make the room NC-25?


The catalog value applies to the diffuser at its stated operating point and under its stated assumptions. The room result also includes terminal and fan sound, other outlets, return-air paths and breakout. Calculate the combined room spectrum before selecting the diffuser.


Should every quiet room use NC-25?


Choose the target according to the room’s use, operator requirements and the acoustic brief. Speech, rest, recording and clinical use can lead to different targets.

For a space sensitive to rumble or tonal sound, agree on additional spectral or sound-quality acceptance requirements with the acoustician.


How do you combine multiple HVAC noise paths?


Combine receiver sound pressure levels by energy within each octave band. Two independent paths at 30 dB each give about 33 dB together. Compare the combined spectrum with the required NC curve.


How is a low-NC design verified on site?


Complete TAB and verify the operating modes first. Measure octave-band sound pressure at the agreed locations with calibrated equipment, document background conditions and apply the specified evaluation method. Record the controlling band and repeat affected checks after corrections.


Conclusion


A low-NC HVAC design starts with a room-specific target and a calculation that follows each significant sound path to the receiver. Treat the band and path that drive the result, preserve the required ventilation and verify the installed system under the operating modes defined in the specification.


Sources and technical references



Technical note:


The NC-25 spectrum and path levels illustrate the method. Project criteria, source data, agreed curve definitions and field measurements govern the final acceptance decision.


Comments


bottom of page