Replacing Fixed-Speed Chillers with Variable-Speed Magnetic-Bearing Chillers in Saudi Arabia
Fixed-Speed Chiller Replacement, Oil-Free Compressor Selection, Part-Load Modeling, and Commissioning for Saudi Plants
Direct answer Compare the fixed-speed baseline and the proposed variable-speed magnetic-bearing chiller using the same delivered cooling, heat-rejection conditions and electrical boundary. Verify peak capacity and stable minimum load, integrate pumps and controls, and measure actual performance after commissioning. |
Replacing a fixed-speed chiller with a variable-speed magnetic-bearing chiller can reduce electricity where the existing plant spends many hours at part load and the new compressor can operate efficiently at the required lift. First verify that the exact chiller can meet the facility’s peak cooling duty, minimum load and installation constraints. A strong part-load rating is useful for screening, but the retrofit decision depends on complete chiller selections and the plant’s measured load and operating conditions.
What changes when fixed-speed chillers are replaced
In an oil-free magnetic-bearing centrifugal compressor, active magnetic bearings support the shaft without an oil lubrication circuit during normal operation. The variable-speed drive changes compressor speed as load and lift vary. Treat these as different features: one changes how the shaft is supported, and the other changes how the compressor matches the operating point.
An existing fixed-speed centrifugal machine may unload using inlet guide vanes. Fixed-speed screw machines can use different capacity-control arrangements, such as a slide valve. Verify how the installed plant actually unloads, stages or cycles.
A variable-speed centrifugal chiller can slow its compressors as operating conditions permit. Its efficiency and minimum stable capacity depend on lift, water temperatures, compressor staging and the OEM operating envelope.
Oil-free compressor operation removes oil management from the refrigeration circuit. The replacement still requires a maintenance plan for its heat exchangers, water treatment, power electronics, bearing controls and sensors.
Chiller efficiency and whole-plant efficiency are different measurements. Include the pumps, tower fans or other allocated auxiliaries consistently. Use the chiller’s rated package input without counting integral fans twice.
Lift is the pressure rise the compressor must provide. Saturated condensing and evaporating temperatures can help characterize lift on a given selection. Ask the OEM for the operating map and expected capacity and efficiency at the site's actual chilled-water and heat-rejection conditions.

Figure 1. Compare measured fixed-speed plant performance with a complete magnetic-bearing chiller selection at matching cooling output and site conditions.
Eight engineering checks for replacing fixed-speed chillers
1. Measure the fixed-speed baseline
Trend delivered cooling, plant electrical kW and kWh, water temperatures, flow, chiller status and relevant heat-rejection conditions. Separate chiller and auxiliary input when possible and include representative high and low loads.
Engineering checks: verified meter boundaries, synchronized intervals, existing load-control method, equipment condition and operating hours.
2. Establish peak duty and redundancy
Reconcile the design load with measured and expected demands. Specify entering condenser-air or water conditions, leaving chilled-water temperature, fluid, flow and site altitude as applicable. Verify full-load capacity and available backup under the approved operating scenario.
Engineering checks: design weather, peak load, chilled-water requirements, condenser conditions and standby capacity.
3. Check the operating envelope and stable turndown
Request OEM selection points and operating maps for the complete chiller. Check the minimum stable load at the required lift, compressor staging, recoverable operating limits and strategy for avoiding unstable operation. Include early morning, low-load overnight and peak summer cases.
Engineering checks: capacity and power at combined load and lift points, staging thresholds, cycling limits and operation near surge.
4. Compare energy using the project's load and weather bins
Use AHRI full-load and standardized part-load ratings for like-for-like screening. For annual energy, use site-specific hours, matched operating conditions and expected part-load performance. Add or meter auxiliaries on the same boundary and sum kWh across the bins.
Engineering checks: project load history, summer and shoulder-season conditions, standby scope and consistent chiller-versus-plant metrics.
5. Prove hydronic and heat-rejection compatibility
Check selected evaporator and condenser pressure drops, available pump head, nozzle locations, minimum flow and permissible rate of change. For water-cooled systems, confirm achievable condenser-water conditions and evaluate tower and pump power alongside chiller power.
Engineering checks: flow limits, water quality, valve and bypass strategy, tower and pump duty, and piping modifications.
6. Verify power, controls and service requirements
Coordinate voltage and frequency, feeder and protection ratings, and any harmonic mitigation required by the electrical design. Check BMS interfaces, power-interruption and restart behavior, alarm visibility and service access. Include OEM startup, spares and technician support in the proposal.
Engineering checks: electrical schedules, drive data, BMS points, service clearances, refrigerant type and warranty scope.
7. Plan the equipment changeover
Verify access and lift paths, supporting structure, water and electrical tie-ins, temporary cooling and the sequence for equipment removal and refrigerant recovery. For phased replacements, test how old and new chillers share load.
Engineering checks: phasing and rigging plans, isolation valves, shutdown windows, temporary cooling and mixed-plant sequence.
8. Commission and verify the retrofit
Perform testing, adjusting and balancing (TAB), OEM startup and functional testing across load, staging and restart conditions. Trend plant power and cooling and compare the reporting period with an adjusted fixed-speed baseline. Record any operating conditions that require a seasonal follow-up.
Engineering checks: matched measurement boundary, sensor calibration, reporting baseline, functional test records and savings verification.
Worked example: fixed-speed and variable-speed plant energy by load bin
Assume the same facility operates for 5,000 hours per year across four representative cooling loads. Each row compares the existing and proposed plant at the same cooling output and matched conditions, including the relevant condenser condition for that bin. The kW/RT values are hypothetical and include in-scope running auxiliaries. For each bin, multiply cooling load in refrigeration tons (RT) by plant kW/RT and annual hours. Account for off-hour standby use separately in a full analysis.
Cooling load and annual hours | Existing fixed-speed plant | Variable-speed magnetic-bearing retrofit |
800 RT × 400 h | 0.72 kW/RT → 230,400 kWh | 0.66 kW/RT → 211,200 kWh |
600 RT × 1,200 h | 0.75 kW/RT → 540,000 kWh | 0.59 kW/RT → 424,800 kWh |
400 RT × 2,000 h | 0.84 kW/RT → 672,000 kWh | 0.52 kW/RT → 416,000 kWh |
200 RT × 1,400 h | 1.00 kW/RT → 280,000 kWh | 0.60 kW/RT → 168,000 kWh |
Total over 5,000 operating hours | 1,722,400 kWh | 1,220,000 kWh |
Illustrative operating electricity savings | 502,400 kWh | 29.2% relative to the fixed-speed baseline |

Figure 2. At the same annual cooling duty, the illustrative operating-bin calculation gives 502,400 kWh less electricity, about 29.2% below the fixed-speed baseline.
Saudi design conditions and replacement constraints
Select air-cooled units for the actual entering condenser-air temperature, including any site recirculation and altitude corrections required by the OEM. For water-cooled units, derive the achievable entering condenser-water temperature from local wet-bulb conditions, tower performance and the operating sequence.
Verify capacity and stability across peak summer, typical operation and minimum load. Some oil-free compressor families are designed for higher lift, but selection must confirm the specific chiller and its full-duty operating envelope.
Review the Saudi Building Code edition and the requirements applicable to the replacement scope. For nonresidential facilities, assess SBC 601 where applicable, together with the project electrical, mechanical and refrigerant requirements. Confirm OEM data for the selected refrigerant and provisions for recovering the existing charge.
For a plant that cannot interrupt cooling, plan phased replacement, isolation, temporary cooling or retained standby capacity. Check that the replacement and the remaining fixed-speed units can operate together under the revised staging sequence.
Project acceptance boundary Confirm peak capacity, the stable operating range, equipment integration and applicable Saudi requirements for the complete replacement. Verify projected energy savings using the agreed baseline and actual operating data. Discuss a magnetic-bearing chiller replacement with ASPAR Engineering |
What to include in a magnetic-bearing chiller replacement RFQ
Give each supplier the same fixed-speed baseline, load bins and site design conditions. Require tabulated whole-chiller performance at the project operating points, an operating map, installation and controls requirements, local service arrangements and a commissioning plan.
RFQ category | Minimum information |
Existing plant and load | Chiller schedules, baseline cooling and electrical trends, condenser conditions, maintenance history and capacity needs. |
OEM thermal and electrical selection | Net capacity and package power at the specified points, full-load and part-load rating basis, operating envelope, drive and power data. |
Water-side and physical interfaces | Design flow, pressure drops, minimum flow, nozzle connections, dimensions, operating weight, access and lifting constraints. |
Controls and continuity | BMS points, staging, restart sequence, backup capacity, phasing and temporary cooling. |
Service and acceptance | OEM startup, warranty, local spares and support, functional tests and savings measurement plan. |
Typical fixed-speed replacement risks to review
Treating a favorable IPLV as the facility’s annual energy result without weighting the site’s actual operating hours and conditions.
Selecting for nominal capacity while overlooking high lift at peak summer or minimum stable load at night.
Comparing the old plant’s measured kW/RT with the new chiller’s package kW/RT while omitting pumps or tower fans.
Reusing the existing piping and pump sequence without checking the new evaporator pressure drop, minimum flow or allowable flow changes.
Omitting power quality, restart behavior or service clearance from the technical comparison.
Assuming magnetic bearings remove all maintenance or replace the need to assess acoustic and vibration performance.
Delivery workflow from fixed-speed baseline to verified replacement
Record the existing fixed-speed plant performance and define the required cooling service.
Confirm site peak duty, typical part-load points and heat-rejection conditions.
Obtain the OEM selections and operating maps for the shortlisted magnetic-bearing chillers.
Compare annual energy over matched load and weather bins and verify integration requirements.
Approve the cutover, temporary cooling and controls strategy.
Complete OEM startup, TAB and functional commissioning at the required conditions.
Compare the retrofit with the adjusted baseline and issue operating and maintenance records.
Consultant checklist for magnetic-bearing chiller replacement
☐ Existing cooling load, lift and power are documented with a consistent meter boundary.
☐ OEM peak and part-load selections cover the actual site condenser and chilled-water conditions.
☐ Minimum stable capacity, surge margin and compressor staging are confirmed across the required operating envelope.
☐ Chiller and auxiliary energy are compared on the same project load and weather bins.
☐ Hydronic, electrical, service, refrigerant and BMS interfaces are checked.
☐ Cutover, temporary cooling, lead–lag control and backup capacity are agreed.
☐ Commissioning, seasonal verification and the savings measurement plan are documented.
How ASPAR Engineering can support chiller replacement
ASPAR Engineering lists oil-free magnetic chillers among its chiller solutions in Saudi Arabia and provides energy audits, engineering analysis and commissioning services. A replacement review can compare the existing plant with model-specific selections and identify the hydronic, electrical and controls changes needed.
Share the existing chiller schedule, plant schematics, trend data, condenser and chilled-water conditions, and any cooling continuity requirements so the comparison reflects the actual retrofit.
Planning to replace fixed-speed chillers in Saudi Arabia? Send the existing equipment schedules, plant baseline, site design duty and required cooling continuity so the team can review magnetic-bearing chiller selections. Request a chiller replacement review — info@aspar.engineer · +966 59 662 9319 |
Related ASPAR Engineering pages and technical guides
These resources cover chiller selection, oil-free magnetic bearings, equipment replacement, metering and plant commissioning.
Frequently asked questions
Do variable-speed magnetic-bearing chillers always use less energy?
The result depends on the operating hours, load, compressor lift, stable turndown and auxiliary power. Compare the complete chiller and plant at matched cooling duty and representative site conditions.
A plant that runs mainly at high lift or near full load still needs a project-specific comparison, even if the replacement has a favorable standardized part-load figure.
What is the difference between magnetic bearings and variable speed?
Magnetic bearings support the compressor shaft electronically and enable oil-free compressor operation. Variable speed is the drive’s ability to change motor speed as capacity and lift requirements vary. The energy result depends on the complete chiller design and the operating point.
Can a magnetic-bearing chiller handle Saudi summer conditions?
Some OEM selections cover higher lift, including hot-ambient air-cooled applications. Verify the exact chiller capacity, input power and operating envelope at the project design conditions, including condenser-air temperature or condenser-water conditions as applicable.
Can the existing pumps, towers and electrical feeder be reused?
Review pump curves, design flow, evaporator and condenser pressure drop, minimum flow, tower capacity and the new electrical ratings. Verify the actual fit, switchgear and protection requirements, and plan any modifications before procurement.
The existing plant may also need a revised control sequence to coordinate the new package with pumps, towers and any remaining chillers.
Is there a model-independent energy savings percentage?
Savings depend on the measured baseline and the proposed plant’s performance across the site’s actual conditions and operating hours. The percentage in the worked example follows from four hypothetical bins and is not a forecast for another installation.
How should a magnetic-bearing chiller replacement be commissioned?
Verify water flow, electrical and controls interfaces, then test the approved sequence at low load and during staging, alarms and restart. Compare measured plant kW and delivered cooling and complete seasonal testing or follow the agreed procedure where peak conditions cannot be reproduced.
Conclusion
A fixed-speed to magnetic-bearing chiller replacement should meet the actual peak and minimum cooling requirements before projected savings drive the decision. Compare complete equipment selections at the site’s load and condenser conditions, coordinate the replacement with existing plant systems, and verify performance using the same measurement boundary.
Sources and technical references
ANSI/AHRI 551/591, performance rating for water-chilling and heat pump water-heating packages.
https://www.ahrinet.org/sites/default/files/AHRI%20551%20591-2026%20SI.pdf
Danfoss Turbocor portfolio, oil-free magnetic-bearing compressor technology.https://www.danfoss.com/en/products/dcs/compressors/danfoss-turbocor/turbocor/
Danfoss Turbocor TTH/TGH, example of a higher-lift compressor application.https://www.danfoss.com/en-us/products/dcs/compressors/turbocor/turbocor-tth-tgh/
Saudi Building Code, SBC 601, nonresidential energy conservation.https://www.sbc.gov.sa/en/BC/Pages/BuildingCode/BCDetails.aspx?codeId=601&year=2024
U.S. Department of Energy FEMP, Measurement and Verification Guidelines, Version 5.0.https://www.energy.gov/cmei/femp/articles/mv-guidelines-measurement-and-verification-performance-based-contracts-version-0
Technical note: The performance values and calculated savings illustrate the load-bin method. Confirm site capacity, operating envelope and savings with OEM selections, measured plant data and an agreed verification method. |

Comments